[FieldTrip] power-frequency figure

[Tzvetan Popov]

Dear Jinyi,
what you’re referring to is time-frequency analysis. From your e-mail I assumed that you’ve already performed frequency analysis, yet apparently not. You can compute the power spectrum bei using something like this:

cfg              = [];
cfg.output       = 'pow';
cfg.method       = 'mtmfft';
cfg.taper        = 'dpss';
cfg.foilim       = [1 20];                          
cfg.tapsmofrq    = 2;             
fft_data= ft_freqanalysis(cfg,data);
Subsequently you can plot fft_data with the functions I mentioned in my previous e-mail.
Note that we have also a video lectures section where you can get some detailed insight into frequency domain analysis. Please have a look here:
http://fieldtrip.fcdonders.nl/video
and also here
https://www.youtube.com/watch?v=QLvsa1r1Voc


best
tzvetan

> Dear Tzvetan, Thanks for your help. First, to plot the spectral power for one channel with the 'ft_singleplotER', how can I calculate the power spectrum with 'ft_freqanalsis'? Can I use the following code to calculate and plot power spectrum? Thanks a lot!
>  
> Best,
> Jinyi
>  
>  
> %% frequency analysis
> cfg              = [];
> cfg.output       = 'pow';%'fourier';%
> % cfg.channel      = 'MEG';
> cfg.method       = 'mtmconvol';
> cfg.taper        = 'hanning';
> cfg.foi          = 2:1:40;                         % analysis 2 to 30 Hz in steps of 2 Hz
> cfg.t_ftimwin    = ones(length(cfg.foi),1).*0.5;   % length of time window = 0.5 sec
> cfg.toi          = -0.5:0.05:4;                  % time window "slides" from -0.5 to 1.5 sec in steps of 0.05 sec (50 ms)
> TFRhann = ft_freqanalysis(cfg, data);
> %% visualize
> cfg = [];
> cfg.baseline     = [-0.9 -0.1];
> cfg.baselinetype = 'absolute'; 
> cfg.maskstyle    = 'saturation';   
> cfg.zlim         = [-3e-7 3e-7];    %
> cfg.channel      = '26';
> figure
> ft_singleplotER(cfg, TFRhann)
>  
>  
>  
> 
> 2014-11-07 1:33 GMT-05:00 Tzvetan Popov <tzvetan.popov at uni-konstanz.de>:
> Dear Jinyi,
> You can use ft_singleplotER to plot the power spectrum of a single channel. If you are interested in the same but for multiple channels than use ft_multiplotER. Finally if you are interested in the topography of a particular frequency you'd specify it in cfg.xlim=[begin end] and call ft_topoplotER.
> Good luck
> Tzvetan
> 
> 
> 
> > Am 07.11.2014 um 00:23 schrieb Jinyi Long <longjinyi at gmail.com>:
> >
> > Dear Sir/Madam, Thanks for your powerful tool. Now I have one question. When I perform the frequency analysis with the function of 'ft_freqanalaysis', how can I plot the power-frequency figure but not 2D time-frequency figure at single channel? Thanks!
> >
> > Best,
> > Jinyi
> > _______________________________________________
> > fieldtrip mailing list
> > fieldtrip at donders.ru.nl
> > http://mailman.science.ru.nl/mailman/listinfo/fieldtrip
> 
> _______________________________________________
> fieldtrip mailing list
> fieldtrip at donders.ru.nl
> http://mailman.science.ru.nl/mailman/listinfo/fieldtrip
> 
> _______________________________________________
> fieldtrip mailing list
> fieldtrip at donders.ru.nl
> http://mailman.science.ru.nl/mailman/listinfo/fieldtrip

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://mailman.science.ru.nl/pipermail/fieldtrip/attachments/20141107/f95d58ae/attachment-0001.html>